1300 square foot house + single car garage. House on hill, 1/2 of house is 2 story, 1/2 1 story. South side of house needs LOTS OF PREP WORK! Paint peeling & flaking off. Want eves & facia white--stucco bottom white--wood siding blue grey--window trim white--and small accents, window sash, and single garage door antique white. (Sherwin Williams paint design colors). 1 base coat, 2 finish coats. Cost in CA.
Paint acts as a protectant on wooden siding, slowing down the rotting process. This makes it incredibly important to fully coat the undersides of corner boards on the exterior of your home. Whether you’re undertaking a DIY house painting endeavor or have hired professionals, you should check corner boards and shutters to make sure they’re fully painted.

Prime. Dark colors, stains (once sealed), and previously unpainted surfaces (drywall, spackle, etc.) will need a primer coat, usually white. NOTE: most paint stores & home improvement centers will now tint primer (at no charge) to match fairly close to the color of the finished coat, that way two coats of primer need not be applied.[6] Although not all surfaces need a prime coat, skip this step at your peril! Dark colors will likely show through the first -- or even the first couple-- topcoats of paint. Sealants and unpainted surfaces like spackle patches will absorb or repel moisture in a topcoat at a different level than the areas surrounding them. Applying a good primer coat will help even out these differences. Primer equalizes a wall to a uniform surface. It's like erasing a canvas before drawing a new picture. Although some will argue the point, you generally don't need to spend a great deal on primer or buy special primer. A cheap, 5 gallon (18.9 L) bucket of plain, flat white paint will usually do the trick and cover a large area. Give your primer at least 24 hours to dry (follow its instructions) before applying a topcoat.


Similar to exterior mold, mold is more likely to emerge in warm and humid areas. That being said, rooms like bathrooms and basements are more prone to mold. To preemptively prevent mold, use paints that are mold resistant. Should you find mold on a wall in your home, you can clean it with a simple solution of one part bleach to four parts water. If the area is large, you may want to leave the cleaning to a professional.
Do the cleanup. When the painting is done, send the painter home and do the cleanup work yourself. This will include rolling up drop cloths and collecting scrapings, removing painter's tape (use a hair dryer on low heat to soften the adhesive), cleaning paint brushes, rollers, and other tools, replacing electric switch plates, outlet covers, and light fixtures, and sealing any leftover paint cans and storing them in a dry, temperature-controlled location.
Dirt and grime are bound to develop on exterior house paint after some time. Luckily, you can easily clean your home with a pressure washer. It’s recommended that you pressure wash your home about five or six years after the initial paint job. For areas like porches and overhangs, you should clean them more often. Taking a garden hose to these areas once a year should do the trick.
Throughout its 35 plus years in business, Shoreline has done extensive work throughout Fairfield County, including cities such as Darien, Westport, Greenwich and New Canaan. Our service area also extends to Westchester County, NY, New York City, and Rhode Island. Browse our portfolio of completed projects for examples of our superior workmanship throughout our operating territory.

While vinyl siding salespeople claim it never needs to be painted, it does lose its color strength over time, and the degree of fading can vary depending on which sides get the most exposure to sunlight. Perhaps it still hasn’t faded, but you don’t like the color much. You can’t go any darker than its current color, though, because the siding is designed to absorb only so much heat, and a darker color could cause it to buckle. Vinyl paint is available in many colors. Brush painting and roll painting vinyl siding costs $43 per 100 sq. ft., and spray painting costs $34 per 100 sq. ft.
Compare offers. The painter offering the lowest rate may not always be the best painter for the job. Indeed, the total cost isn't the only factor to consider when choosing between multiple bids. You'll want to look at contracts side by side to ensure you're making an apples-to-apples comparison. Are the same materials being used? Are the same services included? Does the painter provide a warranty?
Use a roller to paint the rest of the wall. A good method to use is the 'W method'. You start by painting a large 3 foot (0.91 m) square W on the wall. Then, without lifting the roller, you fill in the W.[7] You can paint a wall section-by-section, and do the walls one at a time for best results. It's generally a good idea to use an extension pole for your roller instead of standing on a ladder. Make sure that neither the extension pole nor the roller has plastic handles, as plastic handles are flexible and this makes it difficult to control the painting.
Painting a brand new house with smooth surfaces dramatically reduces prep work. On the other hand, if you’re painting an old home with peeling walls or siding, it’s going to take a lot longer. When deciding whether to hire house painting professionals or do it yourself, take the current state of the paint into consideration. If you’re not up for the challenge of scraping and sanding for hours, you should hire help to get the best results.
Following the same process as the primer, cut in the walls with your chosen paint. For best results, paint one wall at a time. This makes it easier to spread the paint while it’s still wet. Work from top to bottom, rolling the paint in V or W-shaped strokes. Before applying a second coat, wait two to four hours. Then proceed with the same process used for the first coat.
Stripping – $54–$151/100 sq. ft.. “The principle of paint strippers is penetration of the paint film by the molecules of the active ingredient, causing its swelling; this volume increase causes internal strains, which, together with the weakening of the layer's adhesion to the underlying surface, leads to separation of the layer of the paint from the substrate.”— Wikipedia. All the stripper will do is soften the paint. You’ll still have to scrub or scrape it off.
Expect to pay between $600 to $3,500 or $1.25 to $3 per square foot to coat vinyl, with prices likely increasing for the finish. It is one of the more inexpensive siding materials to have repainted, especially with recent innovations in materials. Changing the finish on your siding is not recommended unless it's completely degraded and worn away by the weather. You can save nearly half the vinyl siding installation cost of $4 per square foot by painting rather than replacing. Before adding a new coat to vinyl siding,
×